Black Friday: 10% off, until 2 December 2026.
Promotion terms and conditions

De hoogste korting geldt. Kortingen worden niet gecombineerd. Borg uitgesloten. Productuitsluitingen en maximale kortingspercentages blijven gelden.

Meer over deze actie

Stella – Eleon rear rack 27kg assembly manual

📘 Technische uitleg
Categorie
E-Bike
Subcategorie
Manuals, Workshop
Merk
Stella
Toegevoegd op
18 juni 2026
Leestijd
5 minuten

Important before installation: 

This 27 kg rear carrier is only suitable for bicycles with a mounting point where the bolt is fitted from underneath, via the mudguard, to the ring lock. Not compatible with bicycles with the Mobi-drive system or older models.

This manual can also be used if you 20kg carrier want to replace with the stronger 27kg carrier.

Assembly steps

Step 1: Check the components

Before starting the installation or repair, check that all the required components are present. (The component set supplied with the carrier contains all the items listed below.)

Components supplied: 

Step 2. Required tools

Make sure you have the following tools before you begin:

  • Basic tools for workshop use
  • Awl
  • Fender punch pliers or drill with 6,5 mm HSS drill bit

Step 3: Check the adjustment of the old pannier rack

Check that the current luggage rack is correctly adjusted according to standard OBD0604023. Pay attention to the following:

  • The luggage rack with battery rail must be tilted slightly forwards
  • An angle of 1–3° forwards is correct

Is this not the case? Only then adjust the fitting steps in this document so that the new rack is correctly positioned.

Step 4. Remove the battery rail

Open the controller box

  • Carefully open the housing.
  • Disconnect all wiring.
  • Remove the controller.

Remove the battery cradle

  • Unscrew the battery cradle from the pannier rack.
  • Set it aside for reuse or replacement.

Remove the coat guards

  • Remove both coat guards to gain full access to the pannier rack.

Step 5. Preparing the mudguard

Mark the position of the current rack

  • Apply a piece of tape to the mudguard on both sides, at the front of the pannier rack. This helps to maintain the correct position when fitting the new rack.

Remove the old pannier rack

  • Unscrew the pannier rack and remove it from the bicycle.

Step 6. Mark the positions of the mudguard holes

Temporarily place the new rear rack

  • Attach the rear rack using the two lower bolts. Make sure that the front of the rack is positioned exactly between the pieces of tape previously stuck to the mudguard.

Mark the drill holes

  • Use an awl or marker to mark the position of the mounting holes on the mudguard.
  • Mark the holes in the mudguard so that the rear rack can be secured in the correct position.

Step 7. Fit the bracket by the lock

Preparation

  • Stick a piece of tape on the mudguard at the height of the ring lock.

Positioning the L-bracket

  • Place the small L-bracket on the rear mudguard, in the correct position for fitting by the lock.

Mark the hole

  • Mark the position of the hole on the tape where the L-bracket will be secured through the mudguard.

Step 8. Make a hole in the mudguard

Remove the rear wheel

  • Remove the rear wheel from the bicycle to access the mudguard properly.

Remove the existing bolt near the lock

  • Unscrew the bolt that attaches the mudguard near the ring lock.

Make a new hole in the mudguard

  • Use a mudguard punch or a drill with a 6,5 mm HSS drill bit to make the previously marked hole in the mudguard.
  • Note: work carefully to avoid damaging the mudguard.

Step 9. Check the positions of the holes in the mudguard

Check the alignment

  • Compare the marked holes on the mudguard with the 4 holes in the strip on the inside of the mudguard.

Correct if necessary

  • Does the alignment differ? → Move the rear rack slightly further forwards so that the holes line up neatly.

Step 10. Making holes in the mudguard

Drill the holes at the marked positions

  • Use a mudguard punch (or a drill with a 6,5 mm HSS drill bit) to make the holes in the mudguard at the marked points.
  • Make neat, round holes that align properly with the mounting strip.

Remove the tape

  • Remove all pieces of tape from the mudguard.

Step 11. Installing the pannier rack

Attach the pannier rack at the bottom

  • Mount the pannier rack to the rear dropouts of the frame using the supplied bolts.

Secure the bracket and mudguard

  • Place the L-bracket over the previously drilled hole near the lock.
  • Attach the mudguard strip and bracket with two M5-bouten to the front of the pannier rack.

Step 12. Installing the L-bracket and attaching it near the lock

Secure the bracket with the mudguard to the frame

  • Secure the bracket together with the mudguard to the frame near the ring lock, using an M5-bout.

Mount the small L-bracket under the mudguard

  • Attach the L-bracket from underneath the mudguard using an M5-bout.

Mount the M6-bout in the frame

  • Insert the M6-bout through the L-bracket and tighten it into the frame.

Final check

  • Check that all the bolts on the pannier rack and mudguard are tightened securely.

Step 13. Installing and connecting the battery cradle

Mount the battery cradle

  • Attach the battery cradle to the new pannier rack. 

Connect the controller

  • Connect the wiring to the controller correctly according to the colour or connector coding.
  • Check that all connections are securely fastened.

Close the controller box

  • Replace the cover on the controller box and click or screw it firmly shut.

Step 14. Fit the rear wheel

  • Fit the rear wheel to the bike, including all accessories (chain/brake/gears).

Step 15. Fit the luggage carrier straps and skirt guards

Fit the luggage carrier straps

  • Replace the luggage carrier straps on the new luggage carrier and attach them at the usual mounting points.

Attach the skirt guards

  • Refit the dress guards.

Deviation from the work instructions

If the installation does not go as planned, follow the steps below to resolve the problem:

1. Check the components

  • Are all the required components present and correct?
    • ❌ Are not all components correct or complete?→ Find the correct components and start the instructions again.
    • ✅ Is everything correct?→ Continue to step 2.

2. Check the steps completed

  • Are all steps completed correctly and in the correct order?
    • ❌ Were any steps skipped or performed incorrectly?→ Carefully repeat the instructions from the relevant step.
    • ✅ Was everything completed correctly?→ Continue to step 3.

3. Contact support

  • Still unable to resolve it? → Contact our technical support via info@blits.bike.
Winkelwagen
Good morning 👋Blits

How can we help you?

Kies hoe je contact wilt opnemen. Blits repareert geen Ananda-motoren.

Bestaand ticket terugvinden

Wil je iets aanvullen op je eerdere vraag? Reageer via de beveiligde ticketlink in je e-mail. Ben je die mail kwijt? Ontvang opnieuw een link naar je open ticket. Bij meerdere open tickets ontvang je voor ieder ticket een mail.

Een andere vraag? Gebruik het formulier hieronder voor een nieuw ticket.